收藏本站
Troubleshooting (continued)
Condition 1:
Applicator
will not heat
Allowable Resistance
3. Check to make sure that power cord is plugged in and that the
electrical outlet has power. If there is no power, contact an
electrician. If outlet has correct power, proceed to the next step.
4. Disconnect the power cord from the electrical outlet, then remove
the temperature module by unscrewing the fastener and lifting out
(see Figure O). Inspect the module for damage to the pins.
If no damage is found, check the resistance between the pins using
an ohmmeter. If the measured value does not agree with that listed
in Table 2, then the temperature module is defective. Replace it by
ordering the appropriate Temperature Module Kit. See Parts Kit list
Module 1
Module 2
Module 3
Module 4
Module 5
21-26 K ohms
12-16 K ohms
3-5 K ohms
1-1.5 K ohms
0-10 ohms
Table 2
on page 27 on this manual.
If the measured value agrees with that listed in Table 2, place
temperature module aside for re-use and proceed to next step.
Important:
Remove the power cord from the electrical outlet before conducting any
further evaluations or repairs.
Handle Disassembly
!
WARNING
5. Remove the remaining adhesive from the entry track by using a
utility knife to cut off the adhesive stick just before it enters the
Disconnect the electrical power and
make sure the applicator has cooled
to room temperature before
servicing. Failure to disconnect the
electrical power or failure to allow
applicator to cool before servicing
may cause electrical shock or
burns.
white sleeve assembly, and gently remove it.
Refer to Figure P for steps 6 through 8.
!
Caution
Do not pull adhesive stick from the
rear of the applicator while in
operation. Removing adhesive
from the rear may cause molten
adhesive to flow out the rear of the
applicator which may cause burns
or damage the applicator.
17
Figure P
6. Remove the stroke adjuster by firmly grasping and twisting upward.
7. Remove the end clip by gently prying off one end of the clip.
8. Slide the transport mechanism off the entry track.
? 3M 2006
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
980892-000 PRINTER RIBBONS
983-009-010R011 BACKSHELL DB9 BLACK PLASTIC
983-10-FRA-4"X18" CONSPICUITY MARKING 4"X 18" WHT
987-1/2-36YD TAPE ATG ADHESIVE TRANSFER 1/2"
999-H15-PS2L571 CONN HD15 FEMALE OVER DUAL PS/2
9EL2 TVS BID 245V 200A
A-1JB CONN JACK AMC 50 OHMS STR SMD
A-DF09LL-WP-R CONN DSUB IP67 FMAL 9POS SLD CUP
相关代理商/技术参数
97-85-14 功能描述:环形MIL规格工具、五金与附件 PLATE SIZE 14 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs
97-85-18 功能描述:环形MIL规格工具、五金与附件 PLATE SIZE 18 RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs
97-85-22 功能描述:环形MIL规格工具、五金与附件 PLATE RoHS:否 制造商:Amphenol Industrial MIL 类型:MIL-DTL-5015 系列:97 产品类型:Dummy Receptacles 用于:97 Series Plugs
97-8522-24 制造商:TE Connectivity 功能描述:- Bulk
97-8522-24-1 制造商:TE CONNECTIVITY 功能描述:
97-8522-25-1 制造商:TE CONNECTIVITY 功能描述:
97-8522-46 制造商:TE Connectivity 功能描述:Z-P HS3 RECP ASY 6R 30P RIGHT - Bulk
97-8522-46-1 制造商:TE CONNECTIVITY 功能描述: